Mon–Fri7:30 AM – 5:30 PM Sat8:00 AM – 1:00 PM
Hearth Roofing · Finished Work

Queens Roofing Job Gallery

This job gallery shows completed Hearth Roofing projects across Queens, each one photographed on the roof by me or my crew.

Roofing and roof flashing across Queens, NY

After: new step flashing and copper counter flashing set into the mortar joints of a brick chimney on an Astoria row house Before: rusted, lifting chimney flashing on the same Astoria row house roof Before After
Before and after: Astoria, attached row house. Rusted chimney flashing removed, new step and counter flashing set into the mortar.
Recent projects by type of work

Recent roofs, sorted by the work

Tap a tab to see only jobs like yours.

New step flashing woven along a dormer wall on a brick two-family home in Sunnyside
Flashing

Sunnyside

Brick two-family home

Loose step flashing along the dormer wall, replaced piece by piece.

New architectural shingles and drip edge on an attached row house in Woodside
Asphalt shingle

Woodside

Attached row house

Worn three-tab shingles off, architectural shingles and new drip edge on.

Replaced and capped parapet wall flashing on a mixed-use building in Ridgewood
FlashingLeak repair

Ridgewood

Mixed-use building

Cracked parapet wall flashing was soaking the store ceiling. Replaced and capped.

Skylight reflashed with a new curb kit on a single-family home in Forest Hills
FlashingLeak repair

Forest Hills

Single-family home

Skylight leaking at the corners, reflashed with a new curb kit.

Sealed pipe boot on the EPDM roof of a Long Island City apartment building
Flat and low-slopeLeak repair

Long Island City

Apartment building

Split pipe boot on the EPDM roof, cut out and sealed.

Flashing detail up close

The joints where roofs let water in

Chimneys get two layers from me. Step flashing weaves under each shingle course, then counter flashing is cut into a mortar joint, bent down over it and sealed. If your chimney or wall flashing has failed, I'll repair it to match these close-ups.

Wall flashing gets the same lapped, tucked finish. Skylights get a full curb kit. Drip edge goes under the underlayment at the eaves, over it at the rakes. And you won't find tar smeared over any joint.

  • Chimney
  • Step
  • Wall
  • Skylight
  • Drip edge
Close-up of finished chimney counter flashing cut into the mortar joint and sealed over step flashing Chimney counter flashing
Three jobs, start to finish

What I found on three roofs and what I did

Each ran from first photo to cleanup. The Bayside job was a full tear-off and re-roof, down to new plywood.

The job AstoriaRow house BaysideBrick two-family CoronaStorefront
Problem found Ceiling leak beside chimney Curled shingles, soft deck Ponding, split seams
Work done New step and counter flashing Tear-off and re-roof Full flat roof replacement
Materials used Aluminum step, copper counter flashing GAF Timberline HDZ, new plywood EPDM, tapered insulation, new drains
Job timeline One day Three days Two days
During the job: exposed chimney step flashing and new underlayment photographed before the shingles cover them During the job

Every layer photographed before it's covered

The photos you get of your own roof

Your roof, photographed the way I see it

  1. 01Estimate
  2. 02During the job
  3. 03Finished

At the free estimate or inspection, I photograph what I find. Once old material comes off, my crew shoots the deck, underlayment and flashing before anything covers them.

At the end you get the finished details and the cleared site, the same kind of shots that fill this job gallery.

Put your roof in the next set of photos

Your roof could be the next one up here

Snap a few pictures of the spot that worries you and send them to me for a look, or book a free estimate and I'll come photograph it myself.